# Smart alternator regulator - **Phone:** 07 8431582 - **Email:** support@example.com - **Address:** 49 Sunnyhills Avenue Glenview Hamilton 3206 New Zealand - [ample power] (https://www.smartregulator.co.nz/why-do-i-need-a-smart-regulator): mastervolt - [smart alternator regulator, zm6, Graeme Polley] (https://www.smartregulator.co.nz/about-us.html): balmar - [Prestolite alternator] (https://www.smartregulator.co.nz/blog/2250185): How to modify a Prestolite alternator for external regulation - [Merc Cruiser alternator modification for external regulation] (https://www.smartregulator.co.nz/blog/2250184): Instructions on Merc Cruiser alternator modification for external regulation - [Configure two ZM6 via switch] (https://www.smartregulator.co.nz/blog/2250183): This diagram shows how to run one main regulator and one in standby with the flick of a switch - [Leece Neville Alternator modification] (https://www.smartregulator.co.nz/blog/642382): Attached drawing shows conversion for external regulation of a Leece Neville alternator - [Delco Remy alternator] (https://www.smartregulator.co.nz/blog/873764): How to configure a Delco Remy alternator, in this case we show a 28Si 12v 200amp alternator conversion - [To configure a LETRIKA alternator regulator ] (https://www.smartregulator.co.nz/blog/791182): Attached drawing shows conversion for external regulation of a Letrika alternator - [Bosch Brush block] (https://www.smartregulator.co.nz/blog/756691): Bosch brush block – ready for external regulation - can be used for N or P switching external regulators, if your unsure make contact and we can assist you $NZ49 See our downloads page for configuration instructions - [ZM6 Temperature Probe Kit] (https://www.smartregulator.co.nz/blog/951691): This kit includes a 3 metre cable, which is fitted with a 6mm ring terminal on one end and spade terminals on the other. For calibration purposes, it comes supplied with two resistors, suitable for setting the device to 50 degrees and 90 degrees. If an alternative temperature setting is required, calibration can be performed using a standard rice cooker. The kit is designed to be used with a ZM6 base unit. It is available for purchase at $30 per kit. Should a different cable length be required, options are available upon request at a cost of $7.00 per metre. - [ZM6 Smart Regulator ( temperature Probe)] (https://www.smartregulator.co.nz/blog/951650): TEMP = a base unit plus a 3 metre temperature loom. The is priced at NZ$350, plus freight charges - [ZM6 Smart Regulator (The works)] (https://www.smartregulator.co.nz/blog/951668): WORKS = a base unit with setup and temp loom. The is priced at NZ$370, plus freight charges - [ZM6 Smart Regulator ( Set Up)] (https://www.smartregulator.co.nz/blog/951649): SETUP = Base unit plus settings to suit your individual setup needs. To request specific settings, please use the form available in the download section. In total, the service costs $350 plus freight charges. - [Alternator conversions/repairs] (https://www.smartregulator.co.nz/blog/756690): We offer a modification service for alternators, which involves disabling the internal regulator and configuring the unit for external regulation. This service is suitable for customers who require more precise or advanced control over their alternator's operation. • Externally Accessible Regulators: $NZ55 • Splitting Case Halves: $NZ95 Pulley supply single A section $65 dual A section $95 - [New Alternators] (https://www.smartregulator.co.nz/blog/951651): All our alternators are fitted with pulley of your choice, configured for external regulation, if not in stock allow 7-10 days. All our alternators are manufactured in Europe for better quality and certainty about performance specifications. We have access to over 3000 different alternators of all shapes and sizes, call for more details. BOSCH 12v 80amp which will bolt directly onto the existing Yanmar mount Quote model A2120S NZ$540 Bosch 12v 120amp alternator This is a good all round and is easy to service and has a single leg mount and single external fan, quote our number A0089 $475 Leitkra 12v 100amp (Earth isolated) single leg mount 52mm single fan quote A9213 $450 Bosch 12v 110amp dual leg, 81mm dual fan, quote A0403 $535 Bosch 12v 120amp dual leg 82mm dual fan, offset adjuster, quote A0065 $540 Bosch 12v 140amp dual leg, 80mm dual fan, offset adjuster quote A0147 $540 Bosch 12v 150amp dual leg, 82mm dual fan, offset adjuster quote A0516S $540 Bos - [Overseas Delivery ZM6] (https://www.smartregulator.co.nz/blog/756696): ZM6 -NZ Post Courier – Australia – East Coast – Approx $40.00 ZM6 – NZ Post – USA – non tracked - $25.00 Approx ZM6 -Courier – USA – $60.00, we can confirm at the time of sending Other locations, call for a quotation,as prices do vary and we charge actual cost with zero markup. - [ZM6 Version 2 User guide and installation instructions] (https://www.smartregulator.co.nz/blog/2213443): ZM6 Version 2 User guide and installation instructions which explains the major change being, current limiting function due to over temperature. March 2026 version - [New Zealand delivery - ZM6] (https://www.smartregulator.co.nz/blog/756694): ZM6 - Courier – NZ non Rural Delivery - $14.00 to business address or + $3.50 for Residential Address ZM6 -Courier – NZ Rural Delivery + $6.0 - [Wire Size Chart] (https://www.smartregulator.co.nz/blog/2244930): Wire size can be confusing, hopefully this chart can assist in determining the correct wire rating - [Ignition Light connection to alternator AC output diagram] (https://www.smartregulator.co.nz/blog/591599): This is a drawing on how to connect an alternator AC output to an ignition light if your alternator does not have a D+ connection. We hold these in stock ready to go - [To configure Hitachi (Yanmar) Alternator] (https://www.smartregulator.co.nz/blog/642385): Attached drawing shows conversion for external regulation of a Hitachi alternator as fitted to YM series and 3 and 4 series Yanmar engines - [ZM6 Smart Regulator ( Base Unit)] (https://www.smartregulator.co.nz/blog/866770): The units are configurable by the user to operate at either 12 Volt or 24 Volt settings. Switching between N-type or P-type is accomplished using on-board jumpers. For installations requiring a 24 Volt setup, please inform us so that we can provide an ignition suppressor. Each unit is supplied with a comprehensive 28-page installation manual and user guide. If your installation requires 24V, please inform us, as we can supply an ignition suppressor to suit your setup. The package also includes a buzzer and light for enhanced functionality. BASE = It is not configured for voltage or polarity; the default is P and 14.7v Absorption and 14.0v Float. The unit is priced at NZ$320, plus freight charges.